Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
They are making several good observations relating to A Step-by-Step Guide to Installing a Bathtub overall in this article down the page.
Installing a bathtub isn't exactly rocket science, but it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult task. If the old tub is readily available, the job can move rapidly; if you need to open up a wall surface to eliminate the old bathtub as well as position the new tub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you might require a specialist plumber to make tube links.
This short article will help you mount a brand-new bath tub in your shower room if you have already bought a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist need to consist of the following:
Getting ready for the Installation
To start with, the supporting structure provided with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be rather problematic because of the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub up until the level reviews degree.
To set up faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind needs to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a stiff seal, creating the water to pass through the wall in between the bathroom and the tiling, bring about complications with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that review about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Sharing is nice. Helping people is fun. Many thanks for your time. Visit again soon.
Request Estimate Report this page